Home > Bsod When > BSOD When Rendering Video BCCode: 124

BSOD When Rendering Video BCCode: 124

You should swap it with another known good one for accurate checking. I need my computer to be in good working order. run from boot as this program has its own interface and runs independent of OS. Often it will be the cache memory in the CPU and that error can be caused by incorrect voltage settings in the default BIOS settings for the CPU. (it is why http://ezsolutionsoftware.com/bsod-when/bsod-when-gaming-lag-multitasking.html

Also select Advanced-->Round off checkingto detect core failures ( see reply #1). Perhaps swap it out for one that uses slightly less power than the one installed now. I run at 1920x1080. If it is not, replacing the MoBo under warranty should be the next step.

As i said earlier, only reliable way to test a CPU is swap it with another known good unit. I'll have to look more closely. And it can be changed from +0.5v to 0.25v but I already tried to change it but wasnt the solution Vitor GadiOct 11, 2014, 3:39 PM johnbl said: I am confused, In the last 2 months I've changed everything in my PC, except my RAM memory and HDD.

Back to top #20 Anshad Edavana Anshad Edavana BC Advisor 2,805 posts OFFLINE Gender:Male Location:India Local time:02:50 AM Posted 23 October 2013 - 11:03 PM Hi Prime95 will automatically Best example is"GTA 4". Back to top #27 sflatechguy sflatechguy BC Advisor 1,952 posts OFFLINE Gender:Male Local time:04:20 PM Posted 30 October 2013 - 10:37 PM I would also recommend pulling the video card So instead of a security check failure bugcheck you get bugcheck 124.

My GPU was working just fine with my 2nd generation intel i3 and my old MotherBoard. Here is the message I was greeted with when I logged into windows: Problem signature: Problem Event Name: BlueScreen OS Version: 6.1.7601. Locale ID: 1033 Additional information about the problem: BCCode: I suppose that does make sense. I have even tired to use every symbols package they have for windows 7 none work.

Upon researching, I found that sudden restarts are the new BSOD in windows 7. Coupon Guide Store Exclusive Steeds Play Free Now What's New? I have to reboot so many times to windows start and sometimes when i power up the PC the power leds don't light up. It's very greatful too see good people who likes to help johnblOct 10, 2014, 8:26 PM added a edit to the last post about the VCCPLL, be sure to look at

Voltages are set to "auto", so perhaps I should manually adjust them? permalinkembedsaveparentgive gold[–]Mashed_up 0 points1 point2 points 4 years ago(2 children)2 things the same do not necessarily mean they will always behave the same (if that makes sense :) ) you could buy two up vote 2 down vote favorite About a month ago my computer started experiencing crashes, at first it was just every once in a while, then it escalated to around 5 But it looked like none of the cores failed.

EDIT: I forgot to mention that when it suddenly restarts, the BIOS halts saying "hyper transport sync flood error" press F1 to continue. 14 commentsshareall 14 commentssorted by: besttopnewcontroversialoldrandomq&alive (beta)[–]TexSC[S] 0 points1 point2 weblink All tests passed - Core Temp registered a CPU temperature high of 55 degrees C. If you buy a higher CPU, you won't lose the money even if the old one is not faulty. John, I had a Sentet BXP450 (450w) I was not sure if this a real 450w por supply (In Brazil we use "real" to specify if the power supply really delivery

Of course when I set the CPU back down to stock speed (with stock voltages), I didnt get the error... The first thing I would try is to go back to normal clock speed. Then try again to crash it. http://ezsolutionsoftware.com/bsod-when/bsod-when-loading-presumably-bitdefender.html This will help when searching knowledge bases.

Much appreciated. Fortunately, they have a three year warranty on their motherboards -- so I can technically still RMA it until January. I have a lot of them hahahaha!

None of the reallocated sector counts are over 100, also attached a screenshot of Crystal disk.

So enter BIOS setup and load default values to revert any possible voltage tweaks. Middle-earth Poster Map © 2007 SZC under license.   Europe United States and Canada This form's session has expired. Look for any events marked Critical or Error. John, I had a Sentet BXP450 (450w) I was not sure if this a real 450w por supply (In Brazil we use "real" to specify if the power supply really delivery

I just moved from PA to NV, then from NV to TX all within the last few months. The MSDN article shows that it's a hardware check failure. Maybe the new CPU will take care of the BCCode 124, STOP 0x124 and the HTSFE -- and a new graphics card will take care of the rest... http://ezsolutionsoftware.com/bsod-when/bsod-when-burning-dvd-s-using-convertxtodvd.html A good power supply will not allow the computer to boot until all lines are at the correct voltage for that line.

Graphics card - this always happens while playing games. Edit: Another strange occurrence. But I have a question: Sometimes my PC reboot/loss video BEFORE windows boot process. Other info: when I first logged onto the new computer and loaded LotRO, I didnt have sound until I went into LotRO audio and selected the 'generic software for RealTek' and

it sounds like this chip wants more voltage. If the new CPU doesn't fix things, I'm going to RMA. No more than 4 GB is used, though, even though I have 12 GB installed. I foun this on Intel's website: https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=19763You think It could help me?

I'm going to go up and switch to a Blend Test, and let that run for at least two hours as well. This time it did make an event. Thanks a lot, John. My friend is not having any problems and can run Furmark fine for hours.

I have attached the SF Diagnostic for starters and hope i can get some help from here, thanks. R. permalinkembedsavegive gold[–]TexSC[S] 0 points1 point2 points 4 years ago(3 children)As I stated, I built 2 identical computers. I ran memtest86 and found tons of errors, I then went out and bought new RAM, tired rendering again, but still got BSOD, re did memory test and had 0 errors,

I received and installed my new CPU today. Sense OCZ toolbox didn't find the Drive I took it out and booted to Windows 7 CD and install a new OS on one of my seagate drives, I then attempted Now, I'm not as Familiar with AMD systems as I am Intel, but the bios error could mean an error in the "Hypertreading" (I don't know what AMD calls it, or John, I had a Sentet BXP450 (450w) I was not sure if this a real 450w por supply (In Brazil we use "real" to specify if the power supply really delivery