Home > Windows 7 > Service Pack Installation Failed With Error Code 0x800f0a12.

Service Pack Installation Failed With Error Code 0x800f0a12.

Contents

I've been trying for months to find an update solution. FOR PRESIDENT !! Does amyone have any ideas on what I could do to fix this? Figure B The System Image Recovery procedure will immediately locate the most recent system image connected to your system. have a peek here

Thanks again! Your best bet is likely to search for solutions to your specific error code (0x80070057). A few sentences in on your article and I knew that you knew what you were talking about, followed your instructions and :Wala", thankyou kindly. I was sick to death of windows 10 and it's propensity for spying on the user..Daniel Roy January 7, 2017 Reply If you were into conspiracy theories, you might conclude that

Service Pack Installation Failed With Error Code 0x800f0a12.

What I didn't realise is that because I run with UAC disabled I automatically had the SP backup files included in my last clean-up run. To this point I havent seen one of the above suggestions resolve this issue so you might want to go back and do them all again? I have been running the RC since it's launch and came to update to the RTM version yesterday. I can see that this page is going to get used quite a lot.Thank you so very very much for this easy to follow resolution.

Reply joscon [Microsoft] says: January 11, 2017 at 8:39 pm Awesome, glad that worked out for you. -Joseph Reply joscon [Microsoft] says: January 11, 2017 at 8:39 pm So Danielle, you Merry Christmas. However, Windows Update issues have frequently plagued Windows 7 over the last year, and this has been particularly troublesome for fresh Windows installs. Windows 7 Service Pack 1 Download Raid configuration is to stripe (I'm looking for speed).

I believe I've tried everything in this thread and still no luck. Windows 7 Sp1 Error 0x800f0a12 Dual Boot Luis January 10, 2017 Reply Great Article. I realize there are Diskpart commands like this: > sel disk=system > sel part=1 > det part However that assumes you already know where the active parition is, else you might The whole thing looks for me like Microsoft is falling back in darkest times, when the company assumed being the one and only in the world and e.g.

So you have to set the boot flag to system (with gparted, for instance) Reply ArKay says: February 23, 2011 at 3:28 pm Again MS messed up. Sfc /scannow FOR PRESIDENT !! Unfortunately, when I booted windows it does something so that it becomes the boot partition and I don't get the GRUB menu any more. I have no idea if this has had any additional affect.

Windows 7 Sp1 Error 0x800f0a12 Dual Boot

Dan December 23, 2016 Reply At step 6 it would not offer to install so I jumped to 10. No Reboot necessary Reply kourosh says: March 1, 2011 at 12:36 am i have a vaio F125 i did both disk management and diskpart steps then we i restarted the PC Service Pack Installation Failed With Error Code 0x800f0a12. Thank you so much for all the help. Windows 7 Service Pack 1 Offline Installer Again - Thanks!

I spent hours searching for a solution. navigate here It was driving me crazy not being able to update now its fixed and my laptop is operating correctly again.thanks againsteve Greg November 27, 2016 Reply Thanks heaps for this article Andy D. Andy D. Kb976932

each time one failed I would do another fresh install of windows (Just to make sure I didn't copy over some junk or something that may cause problems later on).Then I Reply Mohit says: July 13, 2011 at 5:48 pm @ Joseph, It really worked for me thanks alot. You can then format the drive using Windows 7, without encountering the invalid-product-key error at activation time.In the event that the same activation error pops up after you've followed these instructions, Check This Out Just system partition.

Reply nz says: February 25, 2011 at 10:28 am OK, finally I was able to install the service pack. Download Windows 7 Thank you so much! God ahead with your great job !!!

windows6.1-kb3125574-v4-x64_2dafb1d203c8964239af3048b5dd4b1264cd93b9 so what now?

Reply joscon [Microsoft] says: January 11, 2017 at 8:39 pm Excellent Greg, glad it worked out for you. Much. Just make sure that your primary hard drive has a qualifying previous version of Windows installed on it, and then boot from the Windows 7 DVD and select Custom (Advanced) as Windows 7 Update Stuck Thank you!

It has all gone through OK now, after doing the automount enable trick. Reply joscon [Microsoft] says: January 11, 2017 at 8:39 pm Sure thing, glad to help as much as I can. Why do these Dothraki look calmer than expected? http://ezsolutionsoftware.com/windows-7/can-39-t-uninstall-windows-7-service-pack-1.html there are 4 partitions - 2 are marked "OEM Partiton" (1.5GB which i assume is the light OS, and 10GB which i presume is the recovery partition) and Disk Management can't

Joe Nechanicky December 27, 2016 Reply I just installed W7 pro on a computer; this is second install this week. Rebuild the BCD store on your system by booting into WinRE and run the command: bootrec /rebuildbcd to rebuild the file Lastly, disconnect any external devices, particularly storage devices such as So, maybe I missed something, or your instructions can have an edit….